Sep 13, 2025 Leave a message

Methods of process inspection

First Article Inspection (FII)

FII, also known as the "first-article inspection system," is a proven effective measure through long-term practical experience in identifying problems early and preventing batch-wide product scrap. FII can uncover systemic causes such as severe wear or incorrect installation of jigs and fixtures, deterioration in measuring instrument accuracy, misreading of drawings, or errors in material input or formulation. This allows for corrective or improvement measures to prevent batch-wide nonconformities.

 

FII is typically performed in the following situations:

 

First, when a batch of products begins production;

 

Second, when equipment is readjusted or there are significant changes in the process;

 

Third, when there are changes in shifts or operators;

 

Fourth, when there are changes in the type or material of the raw material.

 

FII generally employs a "three-inspection system": self-inspection by the operator, re-inspection by the team leader or quality inspector, and specialized inspection by the inspector. The final approval of the first article after inspection must be obtained from a dedicated inspector. The inspector should mark the qualified first article with the prescribed mark and retain it until the shift or batch of products is completed. For mass-produced products, the "first piece" is not limited to one piece, but rather involves inspecting a certain number of samples. This is especially crucial for processes where tooling is a primary influencing factor (such as stamping), where first piece inspection is paramount, and the positioning accuracy of the mold must be repeatedly calibrated. To ensure accurate tooling positioning, a positioning accuracy tolerance pre-control method is generally used. This involves repeatedly adjusting the tooling to keep the positioning dimensions within a pre-control line of 1/2 tolerance. This pre-control conforms to the principle of normal distribution, and the United States also uses this method in its defect-free movement. During their time at BBK Electronics, they placed great emphasis on first piece inspection in IPQC. After all, domestic companies engaged in AV appliance production have low levels of process automation and rely heavily on employee operation control. Therefore, first piece inspection during new product production and pull production can prevent many quality problems related to materials and processes, achieving a combination of prevention and control.


Patrol Inspection: Patrol inspection involves inspection workers going to the work site or production area at regular intervals and along designated routes to check whether newly processed products meet the requirements specified in the drawings, processes, or inspection instructions. In mass production, patrol inspection is generally combined with process control charts. It is a crucial measure to alert workers to abnormal conditions in the production process and prevent batch defects. When patrol inspection detects a problem in a process, two tasks should be performed:


Identify the cause of the abnormality and take effective corrective measures to restore the process to normal.

 

Re-inspect and screen all products produced between the last patrol inspection and the current inspection to prevent defective products from flowing to the next process (or the customer).

 

Patrol inspection is conducted chronologically according to the production process, thus facilitating the assessment of changes in the production status of each process over time. This is extremely beneficial for ensuring the quality of the entire batch of processed products. Therefore, it is important, yet often overlooked, that products processed in a particular process should be stored in chronological order.

 

Last-piece inspection: For processing steps that rely on molds or equipment to ensure quality in rotating production, establishing a "last-piece inspection system" is essential. This means that after a batch of products is completed, a comprehensive inspection of the last processed product is conducted. If defects are found, the molds or equipment can be repaired before the next batch is put into production to avoid production disruptions due to mold repairs after the next batch is put into production.

 

Process inspection is a crucial link in ensuring product quality. However, as mentioned earlier, the role of process inspection is not simply to check quality, but to closely integrate with process control to determine whether the production process is normal. Typically, first-pass inspection, patrol inspection, and the use of control charts should be effectively coordinated. Process inspection is not merely a checkpoint; it must be closely linked to quality improvement, transforming inspection results into information for quality improvement, thereby enabling action to be taken for quality improvement. Finally, it should be pointed out that two issues must be fully considered during process inspection: first, familiarity with the dominant factors affecting processing quality listed in the "Process Quality Table"; and second, familiarity with the requirements of process quality management for process inspection. The Process Quality Table is the core of process management and one of the important bases for compiling "Inspection Instructions." The Process Quality Table is generally not directly distributed to the production site to guide production, but various management charts, including inspection plans, should be developed based on the "Process Quality Table" to guide the production site.

 

For processes identified as process management points, they should be the focus of process inspection. In addition to checking and supervising operators to strictly implement the process operation procedures and process management point regulations, inspection personnel should also conduct patrol inspections to verify changes in the quality characteristics of quality management points and the dominant factors affecting them, check whether the operators' inspections and records are correct, and assist operators in analysis and taking corrective measures.

Send Inquiry

whatsapp

Phone

E-mail

Inquiry